
Frequently asked questions
Answers about window and door faults, repairs and maintenance.
Other topics
Other questions
1.Why are the windows fogging up on the inside?
Humid room air condenses on cold glass. Measure the room humidity and check the air extraction.
Open answer Check the risk of condensationShare the answer2.Why is the glass fogging up on the outside?
The outside surface may cool down and become covered with condensation at night. Check whether the moisture is actually on the outside.
Open answer Check the risk of condensationShare the answer3.Why is there condensation between the panes?
If the moisture cannot be wiped off from either the inside or the outside, it is likely that the insulating glass unit has lost its seal.
Open answer Check the risk of condensationShare the answer4.Why is the insulating glass unit fogging up only at the edges?
The edge is often colder than the centre. Check the humidity, air movement near the glass and the type of spacer bar.
Open answer Check the risk of condensationShare the answer5.Why is only one window fogging up?
Compare the humidity, radiator, curtains and glass temperature in that room with those of the other windows.
Open answer Check the risk of condensationShare the answer6.Why are the windows fogging up in the morning?
Moisture accumulates overnight, while the glass cools. Compare the room humidity in the evening and in the morning.
Open answer Check the risk of condensationShare the answer7.Why are the windows fogging up after a shower?
A shower temporarily increases humidity. Check whether the extractor is working and whether air can enter the bathroom.
Open answer Check the risk of condensationShare the answer8.Why are the windows fogging up while cooking?
Cooking produces steam. Check whether the extractor hood removes air outside and whether the room receives replacement air.
Open answer Check the risk of condensationShare the answer9.Why does ice form on the window?
Moisture can freeze on a very cold surface. Determine whether the ice is on the glass, the seal, or the installation joint.
Open answer Advice from a specialistShare the answer10.How is the dew point related to glass?
When the inner pane cools to the dew point of the room air, water may appear on it.
Open answer Check the risk of condensationShare the answer11.Do curtains increase condensation?
Thick curtains can restrict the movement of warm air near the glass. Compare the glass temperature with them pulled back.
Open answer Check the risk of condensationShare the answer12.Does a wide windowsill increase condensation?
The windowsill can direct heat from the radiator away from the glass. Check how the air rises near the window.
Open answer Check the risk of condensationShare the answer13.Does the radiator cover interfere?
The cover can weaken the airflow along the glass. Compare whether the glass warms up when the radiator is uncovered.
Open answer Advice from a specialistShare the answer14.Why is the windowsill wet?
Determine whether the water runs down from the glass, enters through the joint when it rains, or appears only on a cold surface.
Open answer Advice from a specialistShare the answer15.Why is the window reveal becoming moldy?
Check the humidity, the surface temperature, and whether water is entering from outside.
Open answer Advice from a specialistShare the answer16.Why is there mold behind the curtains?
Air moves less effectively behind dense material, so the area may remain colder. Check the humidity and the air gap.
Open answer Advice from a specialistShare the answer17.How can I check the humidity in the room?
Place the hygrometer away from the radiator and glass. Compare the morning and evening readings.
Open answer Check the risk of condensationShare the answer18.How can I measure the glass temperature?
Measure in the problem area and in the center. Reflections from the glass can distort the result for an infrared thermometer.
Open answer Advice from a specialistShare the answer19.Can new windows have more condensation?
Replacing leaky windows can reduce natural air exchange. Check the extraction and indoor humidity.
Open answer Advice from a specialistShare the answer20.What does microventilation do?
The hardware leaves a small gap for air. The actual airflow depends on the conditions and a working extractor.
Open answer Advice from a specialistShare the answer21.How does an air inlet differ from microventilation?
An air inlet is a separate air intake element. Microventilation lets air in through the gap left by the hardware.
Open answer Advice from a specialistShare the answer22.How does an air inlet differ from a heat recovery ventilator?
An air inlet lets air in. A heat recovery ventilator transfers some of the heat from the extracted air to the supply air.
Open answer Advice from a specialistShare the answer23.Does an air conditioner ventilate the room?
A standard household air conditioner circulates room air. The supply of outdoor air must be checked according to the specific model.
Open answer Advice from a specialistShare the answer24.Why can't I feel air coming through the air inlet?
The airflow depends on the pressure difference, wind, and extraction. Check whether the air inlet is open and clean.
Open answer Advice from a specialistShare the answer25.Why is the air inlet whistling?
Check whether the sound changes with the wind or when the extractor is switched on. Inspect whether the air inlet opening is dirty.
Open answer Advice from a specialistShare the answer26.Why does the air inlet freeze over?
A cold surface and humid room air can form ice. Check the extraction and the condition of the unit.
Open answer Advice from a specialistShare the answer27.Can an air inlet be installed without milling?
Some systems are designed for installation without milling. Compatibility is determined by the profile and the specific air inlet instructions.
Open answer Advice from a specialistShare the answer28.Can the seal be cut for an air inlet?
Change the position of the seal only when this is specified in the installation diagram for the specific unit.
Open answer Advice from a specialistShare the answer29.Does an open window let in noise?
Sound travels more easily through an open gap. Compare the sound with the window closed and slightly open.
Open answer Advice from a specialistShare the answer30.How can I check the bathroom extractor?
Check whether airflow can be felt at the grille and whether there is room for air to enter the bathroom.
Open answer Advice from a specialistShare the answer31.Why does the airflow change when the door is opened?
Opening the door changes the airflow path and pressure difference. Compare the extraction with the door open and closed.
Open answer Advice from a specialistShare the answer32.Does a kitchen extractor hood replace ventilation?
An extractor hood usually operates while cooking. For continuous air exchange, check the separate ventilation of the room.
Open answer Advice from a specialistShare the answer33.What does a recirculating extractor hood mean?
It filters and returns the air to the kitchen. Steam removal from the room must be handled through extraction.
Open answer Advice from a specialistShare the answer34.Do heat recovery ventilators need filters?
The supply and extract filters are maintained according to the unit's instructions. Dirty filters can reduce the airflow.
Open answer Advice from a specialistShare the answer35.Why is the heat recovery ventilator making noise?
Check the speed setting, the filters, and whether the sound comes from the unit or from the air outlet.
Open answer Advice from a specialistShare the answer36.Can I ventilate by opening two windows?
Cross-ventilation usually speeds up air exchange. Make sure that the wind does not slam the sashes.
Open answer Advice from a specialistShare the answer37.Why does an open window cool the window reveal?
Cold air flowing for a long time cools the surfaces near the gap. Monitor the room humidity and surface temperature.
Open answer Advice from a specialistShare the answer38.How much heat do I lose when ventilating?
For an approximate power in watts, multiply the airflow in m³/h by the difference between the indoor and outdoor temperatures and by approximately 0.34.
Open answer Advice from a specialistShare the answer39.What does Ug mean?
Ug describes the heat transfer of the insulating glass unit. A lower value indicates lower heat transfer through the unit.
Open answer Advice from a specialistShare the answer40.What does Uw mean?
Uw describes the heat transfer of the entire window, including the glass, frame, and edge of the glass.
Open answer Advice from a specialistShare the answer41.What does Uf mean?
Uf describes the heat transfer of the frame. For the entire window result, the glass and its edge are also important.
Open answer Advice from a specialistShare the answer42.What does Ud mean?
Ud is the heat transfer coefficient of the entire door construction.
Open answer Advice from a specialistShare the answer43.How can I identify the insulating glass unit formula?
Look for the marking on the spacer or in the order documents. The formula indicates the composition of the panes and gaps.
Open answer Advice from a specialistShare the answer44.Is a thicker insulating glass unit warmer?
Compare the declared Ug. The result is determined by the coatings, gas filling, and chamber width.
Open answer Advice from a specialistShare the answer45.Are three panes always quieter?
Noise reduction depends on the pane thicknesses, gaps, and the airtightness of the entire window. Compare the declared acoustic rating.
Open answer Advice from a specialistShare the answer46.What is a warm-edge spacer needed for?
A spacer with lower thermal conductivity helps keep the edge of the inner pane warmer.
Open answer Advice from a specialistShare the answer47.What does a selective coating do?
A low-emissivity coating reduces heat transfer by radiation through the insulating glass unit.
Open answer Advice from a specialistShare the answer48.What is laminated glass?
These are several layers of glass joined by a film. If broken, the film helps hold the shards together.
Open answer Advice from a specialistShare the answer49.Can one pane of an insulating glass unit be replaced?
The panes of a sealed unit form a single product. If one pane cracks, the entire unit is usually measured and replaced.
Open answer Advice from a specialistShare the answer50.Why did the glass crack from the edge?
The cause may be a damaged edge, inadequate support, a load, or uneven heating. It is advisable to photograph the beginning of the crack.
Open answer Advice from a specialistShare the answer51.Do dark blinds heat the glass?
They can increase local heating. It is important how close they are and how strongly the sun heats the glass.
Open answer Advice from a specialistShare the answer52.Can film be applied to the glass?
Check the film's compatibility with the unit. An unsuitable combination can change the heating of the glass.
Open answer Advice from a specialistShare the answer53.How do you measure an insulating glass unit?
For an initial assessment, the dimensions of the visible part are suitable. Production requires the actual dimensions, thickness, and composition of the unit.
Open answer Advice from a specialistShare the answer54.Can a double-glazed unit be replaced with a triple-glazed unit?
Check whether the frame accepts this thickness and whether the hardware will withstand the additional weight.
Open answer Advice from a specialistShare the answer55.Why is the new insulating glass unit heavier?
An additional or thicker pane increases the mass. The sash supports and hardware must be assessed according to the new weight.
Open answer Advice from a specialistShare the answer56.What are insulating glass unit setting blocks needed for?
Load-bearing blocks take the weight, while spacer blocks maintain the gaps. The layout depends on the sash type.
Open answer Advice from a specialistShare the answer57.Why does the lower corner of the glass touch the profile?
Check the insulating glass unit supports and the sash geometry. Adjusting the hinges alone may not eliminate the cause.
Open answer Advice from a specialistShare the answer58.Can the drainage be covered with a setting block?
The blocks must maintain the support and leave the water path specified by the manufacturer unobstructed.
Open answer Advice from a specialistShare the answer59.Why does the insulating glass unit rattle?
Check the glazing beads, gaskets, and spacer blocks. Avoid dismantling a heavy sash yourself.
Open answer Advice from a specialistShare the answer60.Why does the insulating glass unit move in the sash?
There may be a lack of support or proper fastening. An overall view of the sash and the moving area would help the technician.
Open answer Advice from a specialistShare the answer61.Can glass supports be replaced with wood?
Use durable supports suitable for the specific system and designed for the load.
Open answer Advice from a specialistShare the answer62.What is the difference between a load-bearing block and a spacer block?
The load-bearing block carries the weight. The spacer block maintains the required gap and the position of the glass.
Open answer Advice from a specialistShare the answer63.Where are supports installed under the frame?
The locations of the supports are determined by the load path of the construction. They are selected according to the opening and the system's installation diagram.
Open answer Advice from a specialistShare the answer64.What is window drainage needed for?
It directs water that has entered the profile outside. First check whether the factory-made openings are clear.
Open answer Advice from a specialistShare the answer65.Why does water collect in the frame groove?
Check whether water can drain through the drainage and whether the openings were not covered during installation.
Open answer Advice from a specialistShare the answer66.Do new drainage holes need to be drilled?
First determine the profile system and the location of the factory-made channels. Drilling into the wrong chamber can make the situation worse.
Open answer Advice from a specialistShare the answer67.Why does dust enter through the drainage?
Check whether the system-specified external covers are present and whether the water path is clear.
Open answer Advice from a specialistShare the answer68.Why does water enter the room when it rains?
Determine whether the water is coming through the sash, the lower frame, the external sill, or the wall joint.
Open answer Advice from a specialistShare the answer69.Is securing the window with foam sufficient?
The foam insulates the joint. The supports carry the weight, while system-appropriate mechanical fasteners transfer the loads.
Open answer Advice from a specialistShare the answer70.What is the inner installation tape needed for?
The inner layer limits the entry of air and indoor moisture into the installation joint.
Open answer Advice from a specialistShare the answer71.What is the outer installation tape needed for?
The outer layer protects the joint from weather conditions. Select the material according to the entire assembly.
Open answer Advice from a specialistShare the answer72.Why does the installation foam crumble?
Foam that remains exposed for a long time can deteriorate. Check how much thermal insulation remains and whether the joint is properly protected.
Open answer Advice from a specialistShare the answer73.Why is there a draft between the frame and the wall?
First check the tightness of the installation joint. The lowest point where air is felt may differ from the place where it enters.
Open answer Perform a fault analysisShare the answer74.Can the joint be coated with silicone?
Check which layer's function has failed. Surface sealing may not reach the actual air or water path.
Open answer Advice from a specialistShare the answer75.Why is there a gap visible next to the reveal?
Check whether the crack is only in the finish or whether it connects to the installation joint and lets air through.
Open answer Advice from a specialistShare the answer76.How do you check the installation joint under the sill?
Look for air movement, signs of moisture and a cold strip at the connection. Dismantle the finish only after identifying the likely location.
Open answer Advice from a specialistShare the answer77.Must the external sill have a slope?
The windowsill must direct water away from the window. Check the edges, drip edge and joint with the frame.
Open answer Advice from a specialistShare the answer78.Why does moisture appear under the sill?
Distinguish rain ingress from condensation. Check whether the symptom intensifies when it rains or during cold morning hours.
Open answer Check the risk of condensationShare the answer79.Can the window be positioned in the insulation layer?
It is possible if the loads are transferred to the load-bearing structure through designed supports and fasteners.
Open answer Advice from a specialistShare the answer80.How do you choose the position of a window in the wall?
Assess the support, fastening and thermal bridge at the connection. A wall section and the planned insulation are required.
Open answer Advice from a specialistShare the answer81.Can the window be screwed to the polystyrene?
Window loads require a load-bearing structure or a support system designed for this purpose.
Open answer Advice from a specialistShare the answer82.Why does the installation gap change with temperature?
The profile length changes as it heats up and cools down. The gap and fastening must allow the movement intended for the system.
Open answer Advice from a specialistShare the answer83.Why does a dark profile stick in summer?
In sunlight, a dark profile may heat up more. Check whether the symptom disappears in the shade and whether the gaps are sufficient.
Open answer Perform a fault analysisShare the answer84.Can a bowed frame be straightened by adjusting the hinges?
Adjustment changes the position of the sash. If the frame is bowed, its geometry and fastening should be assessed first.
Open answer Advice from a specialistShare the answer85.What is a thermal bridge near a window?
It is a place where heat escapes more easily through the frame or wall connection. The surface there may be colder.
Open answer Advice from a specialistShare the answer86.How do you find a cold joint with a thermal imager?
Compare the zones when there is a difference between indoor and outdoor temperatures. Assess wind, sunlight and reflections.
Open answer Advice from a specialistShare the answer87.Does a thermal imager show air leakage?
It shows the surface temperature. Confirm air movement with a separate inspection.
Open answer Advice from a specialistShare the answer88.Why is the corner near the window cold?
Compare the edge of the glass, the reveal and the frame connection. The cold zone may be caused by different details.
Open answer Advice from a specialistShare the answer89.What should be checked when accepting installed windows?
Check opening, closing, the frame position, drainage, and the documentation for concealed supports and joints.
Open answer Advice from a specialistShare the answer90.Are supports required when installing a panoramic window?
For large elements, the designed load path, base and installation requirements of the specific system are important.
Open answer Advice from a specialistShare the answer91.What should be checked when installing a window in a wooden house?
Take wall movement and settlement into account. The detail must protect the window frame from structural loads.
Open answer Advice from a specialistShare the answer92.How does an installation plate differ from a frame screw?
Their load-transfer and installation methods differ. The selection depends on the wall base and the system.
Open answer Advice from a specialistShare the answer93.Why is the window difficult to close?
Determine whether the sash touches the frame or whether the handle sticks during locking. This helps distinguish between geometry and the drive mechanism.
Open answer Advice from a specialistShare the answer94.Why does the window catch at the bottom corner?
Check for play in the hinges, the sash geometry and the glass supports.
Open answer Advice from a specialistShare the answer95.Why does the window catch at the top?
Check the top gap and the position of the hardware. It is important to know on which side it makes contact.
Open answer Advice from a specialistShare the answer96.Why is the window handle difficult to turn?
Compare whether it is difficult only when closed or also when open. The handle should not be forced.
Open answer Advice from a specialistShare the answer97.Why does the window handle turn freely?
The handle, its spindle or the drive mechanism may be damaged. Check whether the locking points move when turning.
Open answer Advice from a specialistShare the answer98.Why did the handle fall off?
Inspect the fasteners and the base. If the drive mechanism does not move when the handle is turned, the mechanism must be assessed separately.
Open answer Advice from a specialistShare the answer99.Why does the handle not lock at the bottom?
Check whether the sash fits completely against the frame and whether the locking points align with the strike plates.
Open answer Advice from a specialistShare the answer100.Why does the handle turn only when the window is open?
If it moves when open but sticks when closed, check the alignment of the sash and frame strike components.
Open answer Advice from a specialistShare the answer101.Why does the window open in two positions?
The problem may be in the mode-switching area or the upper hardware. Support the sash and do not use force.
Open answer Advice from a specialistShare the answer102.Why does the window not tilt for ventilation?
Determine whether the handle reaches the ventilation position. If it does, check the transmission of movement to the upper hardware.
Open answer Advice from a specialistShare the answer103.Why does the window remain in the tilt position?
Check the handle position and whether the sash can fit against the frame without force. If it is unstable, do not move it.
Open answer Advice from a specialistShare the answer104.What are the upper stays for?
The stays control and limit the opening. Compatibility depends on the hardware system and the sash.
Open answer Advice from a specialistShare the answer105.What is the sash lifter for?
At the end of closing, it helps guide the sash into the correct position. Check whether it reaches the strike component.
Open answer Advice from a specialistShare the answer106.What is the handle blocker for?
It prevents incorrect mode switching. Its operation depends on the sash position and the specific hardware.
Open answer Advice from a specialistShare the answer107.Why is there play in the hinges?
Check whether the hinge itself, its fastening or the sash is moving. Different causes require different repairs.
Open answer Advice from a specialistShare the answer108.Why do the hinges squeak?
Check whether the sound comes from the hinge or from the sash rubbing against the frame. Lubricate according to the manufacturer's instructions.
Open answer Advice from a specialistShare the answer109.Can the hardware be lubricated with a universal spray?
Choose a lubricant approved by the manufacturer. First remove any visible dirt.
Open answer Advice from a specialistShare the answer110.How often should window hardware be maintained?
Follow the system maintenance instructions. Check frequently used or dirty areas more carefully.
Open answer Advice from a specialistShare the answer111.How do you find the hardware model?
Take a photo of the marking on the metal strip and of the entire assembly. The appearance of the handle alone is usually not enough.
Open answer Advice from a specialistShare the answer112.Is hardware from different manufacturers compatible?
Compatibility is determined by the specific system, dimensions, and fastening. Parts performing the same function may differ.
Open answer Advice from a specialistShare the answer113.Why is air coming through near the handle?
Check whether the locking points reach the keep plates and whether the gasket is pressed against the surface in that area.
Open answer Perform a fault analysisShare the answer114.Why is the window letting in air near the hinges?
Check the gaps and the gasket on the hinge side. It is important to distinguish air movement from the effect of cold glass.
Open answer Perform a fault analysisShare the answer115.Why is the window letting in air at the bottom corner?
Check the lower contact of the sash, the gasket's position, and the installation joint next to the windowsill.
Open answer Perform a fault analysisShare the answer116.Why is a draught noticeable only when it is very windy?
Wind increases the pressure difference. Note exactly where on the window or installation joint the airflow appears.
Open answer Perform a fault analysisShare the answer117.What is the difference between a draught and the sensation of cold glass?
In the first case, air enters through a gap. In the second, air near the cold glass cools and descends.
Open answer Perform a fault analysisShare the answer118.How can the gasket be checked with paper?
Close the window over a strip of thin paper and compare the resistance to pulling it out in different places.
Open answer Advice from a specialistShare the answer119.Is it worth increasing the window's compression?
First find the cause of the leak. Excessive compression can make the handle harder to operate.
Open answer Advice from a specialistShare the answer120.Does the window have a winter mode?
Some hardware allows the compression to be adjusted. The aim is uniform sealing according to the instructions for the specific system.
Open answer Advice from a specialistShare the answer121.Why is the handle stiffer after adjustment?
The compression may have increased or the alignment of the locking parts may have changed. Check where resistance is felt.
Open answer Advice from a specialistShare the answer122.Can only part of the gasket be replaced?
It depends on the gasket's design and the damage. It is important to maintain an airtight connection and the correct profile.
Open answer Advice from a specialistShare the answer123.How do you select a new gasket?
The profile system or a cross-section of the old gasket is required. A thicker gasket may put strain on the mechanism.
Open answer Advice from a specialistShare the answer124.Why does the new gasket still let air through?
Check the sash geometry, compression, and whether the leak is not coming through the installation joint.
Open answer Advice from a specialistShare the answer125.Why has the gasket come out of the groove?
Check whether the gasket base matches the groove and whether it is not stretched at the corners.
Open answer Advice from a specialistShare the answer126.Why have cracks appeared in the gasket?
Over time, rubber may lose its elasticity. If the crack coincides with a leak, select a suitable replacement.
Open answer Advice from a specialistShare the answer127.Do the gasket corners need to be glued?
Follow the system diagram. It is important that the corners and joints do not let air through.
Open answer Advice from a specialistShare the answer128.Can a self-adhesive gasket be attached over the old one?
An additional strip can change the position of the sash and make locking more difficult. First find the actual gap.
Open answer Advice from a specialistShare the answer129.How do you clean window gaskets?
Clean it with a mild product and a cloth. Avoid solvents if the manufacturer does not permit them.
Open answer Advice from a specialistShare the answer130.Will replacing the gaskets reduce street noise?
It may decrease if the sound is coming through an unsealed sash gap. Also check the insulating glass unit and the installation joint.
Open answer Advice from a specialistShare the answer131.Why does the gasket stick in winter?
Moisture may freeze at the contact point. Avoid forcing the sash open and check where the moisture is coming from.
Open answer Advice from a specialistShare the answer132.Why do I still feel cold when the window is closed?
Check whether there is a genuine airflow or just a cold glass surface. These are different causes.
Open answer Advice from a specialistShare the answer133.Why will the balcony door not open?
Check whether the handle stops earlier or turns all the way, but the sash remains closed.
Open answer Advice from a specialistShare the answer134.Why has the balcony door sagged?
Check the hinges, sash geometry, and glazing supports. After adjustment, check all the locking points.
Open answer Advice from a specialistShare the answer135.Why will the balcony door not lock from the outside?
Check the balcony latch and its keep plate. The door position and latch compatibility must match.
Open answer Advice from a specialistShare the answer136.Can a balcony door latch be installed?
You need to know the profile, hardware system, and sash gap. A photo from the side of the sash and frame would help.
Open answer Advice from a specialistShare the answer137.Why does the balcony door scrape the threshold?
Determine where it scrapes. Check the hinges, gaps, and whether the threshold has shifted.
Open answer Advice from a specialistShare the answer138.Why is the exterior door letting in air from below?
Check the lower gasket or brush seal, the fastening, and the gap below the sash.
Open answer Perform a fault analysisShare the answer139.Why is the exterior door letting air in near the lock?
Check whether the locking points enter the keep plates and whether the compression is even in that area.
Open answer Advice from a specialistShare the answer140.Why won't the exterior door handle lift?
Do not use force. Check whether the sash closes fully and whether the locking points align.
Open answer Advice from a specialistShare the answer141.Why does the door not lock when the handle is lifted?
The movement of hooks or bolts and the cylinder function depend on the lock model. Check what moves when the sash is closed.
Open answer Advice from a specialistShare the answer142.Why is the door key difficult to turn?
Compare operation with the door open and closed. The difference may indicate the position of the sash or keep plates.
Open answer Advice from a specialistShare the answer143.Why does the key turn but the door does not unlock?
The transmission of movement from the cylinder or lock may be faulty. Do not turn it by force, especially if the key bends.
Open answer Advice from a specialistShare the answer144.Is replacing the door cylinder enough?
If the fault is in the lock gearbox, replacing the cylinder will not fix it. Determine whether the cylinder transmits movement.
Open answer Advice from a specialistShare the answer145.What is a door opening cycle?
One cycle consists of opening and closing. Approximate usage can be estimated based on the number of openings per day and the age of the door.
Open answer Advice from a specialistShare the answer146.Does the number of door cycles indicate hinge wear?
The number of cycles describes the load. The condition of the hinges should be assessed based on play, fastening and the position of the sash.
Open answer Advice from a specialistShare the answer147.Why does the door brush seal not reach the floor?
Check the gap height across the entire width and whether the brush is correctly inserted.
Open answer Advice from a specialistShare the answer148.Can the door threshold gasket be replaced?
Usually, the first things checked are the gasket profile and the condition of the bracket. A close-up photo would help.
Open answer Advice from a specialistShare the answer149.Why does the door only close when slammed hard?
Check whether the sash touches the frame or whether the latch does not align with the strike plate. Avoid slamming it.
Open answer Advice from a specialistShare the answer150.Why does the door closer not close all the way?
Check the sash friction, latch and operation of the closer. Speed adjustment depends on the model.
Open answer Advice from a specialistShare the answer151.Can a door closer be installed?
The door material, dimensions, opening direction and a suitable fastening location are required.
Open answer Advice from a specialistShare the answer152.Why are sliding doors difficult to move?
Check whether the track is clean and whether movement is difficult along the entire path or only in one place. There may be problems with the rollers or geometry.
Open answer Advice from a specialistShare the answer153.Why do sliding doors move jerkily?
Repeated jerking may indicate a problem with the track or rollers. Mark the place where this occurs.
Open answer Advice from a specialistShare the answer154.Why do sliding doors not lock?
Check whether the sash fully reaches the end position and whether the locking points align.
Open answer Advice from a specialistShare the answer155.Why does the sliding door handle not turn?
Do not force it. First, the fit of the sash is checked, followed by the operation of the handle and mechanism.
Open answer Advice from a specialistShare the answer156.Why does water remain in the sliding door track?
Check the drainage holes, drainage path and whether water is entering through the exterior joint.
Open answer Advice from a specialistShare the answer157.Can the sliding door track be lubricated?
Clean the track and check the system instructions. Lubricant in an exposed area may attract dirt.
Open answer Advice from a specialistShare the answer158.Can the sliding door rollers be replaced?
The model, carriage dimensions and sash weight are required. A heavy sash must be removed by specialists.
Open answer Advice from a specialistShare the answer159.Why do sliding doors wobble?
Check whether the sash moves in the guide and whether its fastenings are loose. If the sash is unstable, do not use it.
Open answer Advice from a specialistShare the answer160.Why does the sliding door not fit tightly in one corner?
Check the sash position, supports, rollers and locking points in the specific corner.
Open answer Advice from a specialistShare the answer161.How do lift-and-slide doors differ from tilt-and-slide doors?
A lift-and-slide system raises the sash before sliding. A tilt-and-slide system can move it out of the plane of the frame.
Open answer Advice from a specialistShare the answer162.Why is an aluminum window cold?
Check whether the profile has a thermal insulation chamber and whether the cold spot is at the profile, glass or installation joint.
Open answer Advice from a specialistShare the answer163.Can aluminum doors be adjusted?
The possibilities depend on the hinge system. An overall view of the door and the hinge markings are required.
Open answer Advice from a specialistShare the answer164.Why does a wooden window stick after rain?
Check the coating, water ingress and gaps. Comparing the sash operation after it has dried can help.
Open answer Perform a fault analysisShare the answer165.Can the gaskets of an old wooden window be replaced?
The groove, condition of the wood and fit of the sash need to be assessed. A photo would help identify the profile.
Open answer Advice from a specialistShare the answer166.Why does the bottom of a wooden window turn black?
Check the source of moisture, the condition of the paint and water drainage. Wood that remains damp for a long time should be inspected.
Open answer Advice from a specialistShare the answer167.Can a cracked PVC frame be repaired?
The solution depends on the location and depth of the crack and whether it is in a load-bearing area. The loads need to be assessed.
Open answer Advice from a specialistShare the answer168.Why has the corner of the PVC profile opened?
The effect of a weld seam, loads or deformation is possible. Assess the corner and sash geometry.
Open answer Advice from a specialistShare the answer169.What is PVC profile reinforcement needed for?
Reinforcement increases rigidity. Its shape, thickness and fastening are selected according to the specific profile system.
Open answer Advice from a specialistShare the answer170.How can the thickness of profile reinforcement be checked?
Look for the manufacturer's documents or technical information. The thickness usually cannot be reliably determined from the outside.
Open answer Advice from a specialistShare the answer171.Does the number of chambers indicate how warm a window is?
Use the declared Uw for comparison. The result is determined by the frame, glass unit and their connection.
Open answer Advice from a specialistShare the answer172.Why does the window handle get hot in the sun?
Direct sunlight can strongly heat dark hardware. Check whether the operation of the mechanism has changed.
Open answer Advice from a specialistShare the answer173.Can a PVC window be repainted?
Check the compatibility of the profile and coating. A dark coating may increase heating.
Open answer Advice from a specialistShare the answer174.Why has the window profile turned yellow?
Dirt and surface aging can change the color. Start with a cleaning product permitted by the manufacturer.
Open answer Advice from a specialistShare the answer175.Can a window be cleaned with solvent?
Solvent can damage PVC, coatings or gaskets. Use a cleaner suitable for the material.
Open answer Advice from a specialistShare the answer176.Why can traffic be heard through a closed window?
Compare the noise at the sash, glass and installation joint. Each path may require a different solution.
Open answer Advice from a specialistShare the answer177.What do Rw and Ctr mean?
Rw is the weighted sound insulation index. The Ctr correction helps assess certain low-frequency noise sources, including traffic.
Open answer Advice from a specialistShare the answer178.Are asymmetrical panes quieter?
Different sheet thicknesses can improve the attenuation of certain frequencies. Compare the declared index for the entire construction.
Open answer Advice from a specialistShare the answer179.Why does a closed window whistle?
Whistling often occurs through an air path that is too narrow. Check the edges, trickle vent and connection to the wall.
Open answer Advice from a specialistShare the answer180.Why does the frame vibrate in the wind?
Determine whether the frame, sash, windowsill, or glass is moving. Assess the fastening and supports.
Open answer Advice from a specialistShare the answer181.How can the wind load on a window be assessed?
The location, building height, dimensions, and support diagram are required. The fastening is selected according to the project and system data.
Open answer Advice from a specialistShare the answer182.Why is the window difficult to close only on a hot day?
Compare the sash gaps in warm and cool weather. Check the profile expansion and frame fastening.
Open answer Advice from a specialistShare the answer183.Why is the window difficult to open in cold weather?
Check whether the sash is stuck due to ice and whether the friction disappears when it warms up. Do not use force.
Open answer Advice from a specialistShare the answer184.Can the exterior windowsill make noise?
During rain or wind, loose sheet metal or its fastening may make noise. Check where the noise is strongest.
Open answer Advice from a specialistShare the answer185.What photos should be sent to the technician?
Include an overall view of the window or door, a close-up of the problematic assembly, and a visible marking of the part.
Open answer Advice from a specialistShare the answer186.What should be provided for an insulated glass unit inquiry?
Provide the visible dimensions, a photo, the marking, and a description of the damage. The final dimensions are уточ уточ before production.
Open answer Advice from a specialistShare the answer187.What should be provided for a lock inquiry?
Send photos of the door edge, central lock, and marking. Indicate what does not work when opened and closed.
Open answer Advice from a specialistShare the answer188.What should be provided for a gasket inquiry?
Indicate the window type, where the draft is coming from, and attach photos of the gasket and the entire sash.
Open answer Advice from a specialistShare the answer189.What should be provided for a hinge inquiry?
Send photos of the entire sash and the upper and lower hinges. Indicate where it is sticking.
Open answer Advice from a specialistShare the answer190.Can only one sash be repaired?
If the fault is in one sash, start with it and the corresponding frame area. The scope depends on the cause.
Open answer Advice from a specialistShare the answer191.When is it necessary to call a technician about the glass?
When the glass is cracked, the unit is moving, or there is moisture between the panes. Photos help prepare for the inspection.
Open answer Advice from a specialistShare the answer192.Is it necessary to urgently repair a fallen-out sash?
Do not move an unstable sash and restrict access. A specialist inspection is required.
Open answer Advice from a specialistShare the answer193.How do you arrange a window inspection?
Submit an inquiry with the location, a description of the fault, and photos. Arrange a time once the technician confirms.
Open answer Advice from a specialistShare the answer194.How should you prepare for window repair?
Clear access to the window, remove obstructing items, and be prepared to demonstrate the fault.
Open answer Advice from a specialistShare the answer195.Can windows be repaired in winter?
Many hardware works can be carried out in winter. Manufacturer's working conditions are important for sealing materials and installation.
Open answer Advice from a specialistShare the answer196.How should you maintain a window before winter?
Clean the gaskets and drainage, check the handle operation and even compression.
Open answer Advice from a specialistShare the answer197.How should you maintain a window after repair?
Check all operating positions and follow the maintenance instructions of the technician and hardware manufacturer.
Open answer Advice from a specialistShare the answer198.How do you assess whether the repair was successful?
Compare operation in all positions, handle resistance, fit, and the initial sign of the fault.
Open answer Advice from a specialistShare the answerHistory
199.Why do old houses have smaller windows?
In the past, large and even sheets of glass were more difficult to manufacture. Small window divisions made it possible to assemble a larger opening from smaller panes.
Open answer Advice from a specialistShare the answer200.Why were shutters used in traditional windows?
They limited sunlight and views from outside, but allowed air movement.
Open answer Advice from a specialistShare the answer201.What did the production of large-format glass change?
It made it possible to create wider openings with fewer transoms. The loads from larger glass must still be borne by the frame and supports.
Open answer Advice from a specialistShare the answer202.Why is corner glazing used in modern houses?
A transparent corner expands the view and lets in daylight from two directions. The structures selected according to the project take the loads at the corner.
Open answer Advice from a specialistShare the answer203.How does a panoramic façade differ from an ordinary window?
Panoramic glazing occupies a larger part of the façade. When designing it, support, wind loads, thermal performance, and solar control must all be addressed together.
Open answer Advice from a specialistShare the answer204.Why does a uniform window rhythm change the appearance of a façade?
The height of the openings, verticals, and transom lines form the composition. When changing one element, it is useful to compare it with the adjacent windows.
Open answer Advice from a specialistShare the answer205.Why did the insulated glass unit replace individual panes?
The panes and sealed cavity are joined into one unit at the factory. The sealed cavity helps reduce heat transfer.
Open answer Advice from a specialistShare the answerAccessories and catalogues
206.How should the cold-period climate table be used?
It provides outdoor climate data intended for design. For an object in Lithuania, select the relevant local data according to the project methodology.
Open answer Technical catalogueShare the answer207.What are warm-period climate data used for?
They help assess summer overheating, ventilation, and solar control. Assess the data for the specific location and the façade orientation.
Open answer Technical catalogueShare the answer208.How should the map of main and additional profiles be read?
Use the marking to find the cross-section and purpose, then check which parts of the same system it is connected to.
Open answer Technical catalogueShare the answer209.What do the profile combination drawings show?
They show how the frame, sash, divider, or additional profile fit together. Check compatibility according to the marking and the assembly dimensions.
Open answer Technical catalogueShare the answer210.Why do panoramic glazing profiles have separate tables?
They require different load transfer, connections, and rigidity. A window-profile diagram cannot be automatically applied to a façade.
Open answer Technical catalogueShare the answer211.How should the diagram of the maximum sash dimensions be read?
Using the sash measurement reference, find the width and height, then check the weight and the diagram conditions. Use the same profile and hardware system.
Open answer Technical catalogueShare the answer212.Why is it still necessary to check the hardware load diagram?
The profile and hardware have separate limits. The sash width, height, and mass must be checked against both documents for the specific system.
Open answer Technical catalogueShare the answer213.What does the moment of inertia mean in the reinforcement table?
It describes how the shape of a metal cross-section resists bending about a selected axis. The profile orientation is also important in the assessment.
Open answer Technical catalogueShare the answer214.Where should the colour of the window profile or hardware be checked?
Compare the manufacturer's colour code or a physical sample. A screen image, lighting, and the shade of an old surface can be misleading.
Open answer Technical catalogueShare the answer215.Is the hardware for an arched window the same as for a rectangular one?
Arched and non-standard sashes use configurations intended for their geometry. The curvature, dimensional limits, and specific system must be checked.
Open answer Technical catalogueShare the answer216.How do concealed hinges differ from external ones?
When closed, concealed hinges remain within the frame and sash area. Their adjustment, loads, and opening movement depend on the specific set.
Open answer Technical catalogueShare the answerGlass and structures
Glass and insulating glass units
217.What is tempered glass?
It is thermally treated glass. Check its purpose and requirements according to the product marking and project.
Open answer Advice from a specialistShare the answer218.What is float glass?
It is flat glass whose sheet is formed by the melt flowing over a bath of molten metal. This produces smooth surfaces.
Open answer Advice from a specialistShare the answer219.Can tempered glass be shortened?
Cutting, drilling and edge processing are carried out before tempering. In practice, it is not possible to change the dimensions of an already tempered sheet.
Open answer Advice from a specialistShare the answer220.How does laminated glass differ from tempered glass?
The layers of laminated glass are joined by a film that helps hold the shards together. Tempering changes the mechanical properties of the glass itself and the way it breaks.
Open answer Advice from a specialistShare the answer221.What is an insulating glass unit cavity?
It is a hermetically sealed cavity between two adjacent panes of glass. Two panes form one cavity, and three panes form two.
Open answer Advice from a specialistShare the answer222.What is the spacer frame needed for in an insulating glass unit?
It maintains the distance between the panes of glass. A sealing system is also formed at the edge.
Open answer Advice from a specialistShare the answer223.What does the moisture absorber do in an insulating glass unit?
The absorber binds residual moisture in the cavity. If the edge of the insulating glass unit becomes leaky, it eventually can no longer retain the moisture continuously entering it.
Open answer Check the risk of condensationShare the answer224.Why does an insulating glass unit have two sealing layers?
The primary sealant limits the penetration of moisture and gases. The secondary sealant reinforces the edge joint and helps it withstand loads.
Open answer Advice from a specialistShare the answer225.What is low-emissivity glass?
The low-emissivity coating on the glass reduces heat transfer by radiation. A suitable inner surface is selected for it in the insulating glass unit.
Open answer Advice from a specialistShare the answer226.Why is argon introduced into an insulating glass unit?
Argon helps reduce heat transfer through the enclosed gap. The result depends on the cavity width, tightness and the structure of the entire insulating glass unit.
Open answer Advice from a specialistShare the answer227.Is a wider cavity always warmer?
A gap that is too narrow transfers heat more easily by conduction. In a gap that is too wide, air movement may increase. The appropriate width depends on the gas and the structure of the insulating glass unit.
Open answer Advice from a specialistShare the answer228.What is a warm-edge spacer?
It is a spacer with lower thermal conductivity at the edge. It helps increase the temperature of the inner glass edge.
Open answer Advice from a specialistShare the answer229.Why are panes of different thicknesses used in a quieter insulating glass unit?
The sound insulation of sheets of different thicknesses weakens at different frequencies. Asymmetry helps avoid a common weak point.
Open answer Advice from a specialistShare the answer230.Are three panes always quieter than two?
Sound insulation is affected by pane thicknesses, cavity widths, the laminate, frame tightness and the installation joint. Compare the acoustic data for the entire window.
Open answer Advice from a specialistShare the answer231.Why can a large insulating glass unit bow?
Glass is affected by wind and pressure differences in sealed cavities. The glass dimensions, thickness, support and temperature are significant.
Open answer Advice from a specialistShare the answer232.Why can glass crack when part of it is covered?
Uneven heating creates stresses. The risk is affected by the type of glass, the condition of the edge and shade. The cause cannot be confirmed remotely from the crack alone.
Open answer Advice from a specialistShare the answerProfiles
233.What is a window mullion?
It is a frame element separating the parts of a window. Its rigidity and connections are important for loads.
Open answer Technical catalogueShare the answer234.How does a frame differ from a sash?
The frame is fixed in the opening. The sash is the opening part, connected to the frame by hardware.
Open answer Technical catalogueShare the answer235.What holds the insulating glass unit in a PVC sash?
The insulating glass unit rests on support blocks. Glazing beads and gaskets hold it in the profile and seal the edges.
Open answer Technical catalogueShare the answer236.Why is there steel reinforcement in a plastic profile?
It increases the rigidity of the profile and helps it withstand loads. The reinforcement is selected for the specific profile and structure.
Open answer Technical catalogueShare the answer237.Does the number of profile chambers determine the warmth of the entire window?
The frame, insulating glass unit, edge of the insulating glass unit and the ratio of their areas determine the entire window's value. Compare Uw for evaluation.
Open answer Technical catalogueShare the answer238.Where does rainwater drain from the window profile?
Water from the glazing area is collected in channels and flows out through designated drainage holes on the outside.
Open answer Technical catalogueShare the answer239.Why do dark PVC profiles move more in the sun?
In the sun, a dark surface heats up more strongly. Temperature changes alter the length of the profile, so clearances and system fixing conditions are important.
Open answer Technical catalogueShare the answer240.What determines whether a part from another profile is suitable for an old window?
Check the system marking, cross-section, fixing locations and dimensions. Similar appearance alone does not confirm compatibility.
Open answer Technical catalogueShare the answerHeat and structures
241.What do Uw, Ug and Uf mean?
Uw describes the heat transfer of the entire window, Ug the insulating glass unit, and Uf the frame part. A lower value means lower heat transfer under the same conditions.
Open answer Advice from a specialistShare the answer242.Why can the Uw of windows of different sizes made from the same profile differ?
The ratio of the frame and glass areas and the length of the insulating glass unit edge change. Therefore, the same profile does not mean the same Uw value for the entire window.
Open answer Advice from a specialistShare the answer243.Does a low Ug always mean a warm window?
Ug describes the central part of the insulating glass unit. The frame and the edge of the insulating glass unit are also important for the window's heat transfer.
Open answer Advice from a specialistShare the answer244.How does the heat transfer coefficient differ from thermal resistance?
Greater resistance means greater resistance to heat flow. When constructions and conditions defined in the same way are compared, a lower U corresponds to greater resistance.
Open answer Advice from a specialistShare the answer245.Why is the edge of the glass colder than the centre?
At the edge of the insulating glass unit, heat flows through the spacer, edge sealants and frame connection. The edge temperature may be lower than that of the central glass area.
Open answer Advice from a specialistShare the answer246.How is the risk of condensation near a window assessed?
The temperature of the coldest internal surface is compared with the room air dew point. The air temperature and humidity must be known.
Open answer Advice from a specialistShare the answer247.What does a window temperature field calculation show?
It shows the heat path through the junction and allows the coldest areas to be compared, such as the edge of the glazing unit or the frame-to-wall junction.
Open answer Advice from a specialistShare the answer248.Why indicate the opening direction in a window drawing?
It allows you to check in advance where the hinges and handle will be, whether the sash will open without obstruction and whether it can be conveniently reached.
Open answer Advice from a specialistShare the answer249.Why are wind loads checked before manufacturing a large window?
Wind acts on the glass, mullions, frame and fastenings. The permissible solution depends on the location, height, dimensions and support conditions.
Open answer Advice from a specialistShare the answer250.What does profile deflection mean?
This is the element's deviation from its initial position due to a load. Excessive deflection can affect the edge of the glazing unit, airtightness or opening operation.
Open answer Advice from a specialistShare the answer251.What function does a mullion perform in a panoramic façade?
It takes over part of the façade load and transfers it to the supports. The specific free length, loads and support scheme are calculated.
Open answer Advice from a specialistShare the answer252.Why is the support scheme important for large glazing?
Glass stresses and deflection depend on which of its edges are supported and how the load is transferred to the frame.
Open answer Advice from a specialistShare the answerInstallation
253.What needs to be measured before ordering a window?
Check the opening width and height in several places, the diagonals, the wall structure, the windowsill area and the installation gaps.
Open answer Technical catalogueShare the answer254.Why is the window opening prepared before installation?
Fastening requires a suitable base, while sealing requires clean and sufficiently level surfaces. Crumbling areas must be repaired.
Open answer Technical catalogueShare the answer255.Why is a gap left above the window in a wooden house?
A wooden wall can settle and change dimensions. A suitable junction allows it to move without pressing against the window frame.
Open answer Technical catalogueShare the answer256.What supports the weight of the window in the opening?
The weight is transferred to the load-bearing structure through designated rigid supports. The purpose of installation foam is to insulate the cavity.
Open answer Technical catalogueShare the answer257.What are installation gaps around the frame needed for?
They allow the frame to be levelled, the joint to be sealed and thermal movements to be accommodated. The size depends on the profile, dimensions and system.
Open answer Technical catalogueShare the answer258.Do installation foams replace window fastening?
The loads are taken by the supports and fastening elements according to the wall and window system. Foam fills and insulates the joint.
Open answer Technical catalogueShare the answer259.What should be checked before finally fastening the frame?
Check the horizontal and vertical alignment, the diagonals and whether the profile is not bent. It is advisable to check the sash operation before finishing the joint.
Open answer Technical catalogueShare the answer260.What is the difference between the inner and outer layers of the installation joint?
The inner side limits the entry of indoor air and moisture into the joint. The outer side protects against weather conditions and, depending on the junction, allows the joint to dry.
Open answer Technical catalogueShare the answer261.Why can there be a draught near the windowsill even with a new gasket?
If air is moving between the frame, windowsill and wall, first check the lower installation junction. The sash gasket closes the other joint.
Open answer Technical catalogueShare the answer262.Why is the position of the window within the wall thickness important during installation?
It changes the heat path of the frame-to-wall junction. The appropriate position depends on the wall layers and the insulation junction.
Open answer Technical catalogueShare the answerAdditional glass diagnostics
263.What does the glazing unit formula mean?
It indicates the structure of the panes and cavities. Additional designations may describe the coating, gas, laminate or spacer.
Open answer Advice from a specialistShare the answer264.Why is the position of the low-emissivity coating in the glazing unit important?
The position of the coating is related to the effects of heat and solar radiation. When replacing the glazing unit, check the specified surface and its orientation.
Open answer Advice from a specialistShare the answer265.What is the difference between solar-control glass and low-emissivity glass?
Solar control limits the entry of solar energy. A low-emissivity coating reduces long-wave heat transfer. One product can have both properties.
Open answer Advice from a specialistShare the answer266.What is the difference between visible light transmittance and the solar factor of glass?
Visible light transmittance describes visible light. The solar factor indicates how much solar energy enters the room in total.
Open answer Advice from a specialistShare the answer267.Can you determine that argon has escaped by observing condensation?
The amount of gas cannot be determined from condensation on the room-side surface. Moisture between the panes primarily indicates a possible problem with the glazing unit's airtightness.
Open answer Advice from a specialistShare the answer268.Why must the edge of a glazing unit be protected?
There is a sealing and joining system at the edge of the glazing unit. It is stressed by glass movement, while improperly retained water can worsen performance.
Open answer Advice from a specialistShare the answer269.What is glazing unit resonance?
The panes and the air enclosed between them form a system that attenuates sound less effectively in a certain frequency range. The structure is selected according to the type of noise.
Open answer Advice from a specialistShare the answer270.Why does thickening the glass require the hardware to be reassessed?
Glass mass increases with thickness. Greater mass loads the hinges, stays, profile and supports.
Open answer Advice from a specialistShare the answerAdditional profile and hardware topics
271.Can a window be selected solely by the profile installation depth?
Depth describes one dimension. Compare the thermal, airtightness, load-bearing and glazing installation data of the entire window.
Open answer Technical catalogueShare the answer272.What is the difference between a gasket and a drainage hole?
The gasket limits the passage of air and water through the joint. The drainage hole removes water from the designated area of the profile.
Open answer Technical catalogueShare the answer273.Why must drainage holes not be blocked?
If the designated outlet is blocked, water may accumulate in the profile. If an airflow is felt through the opening, also check the condition of the inner seal.
Open answer Technical catalogueShare the answer274.Why is the position of the window mullions also important for structural performance?
Mullions change the area of the glass fields and the load-transfer path. When designing, their position must correspond to the composition and structural limits.
Open answer Technical catalogueShare the answer275.Why are both the width and height of the sash important for the hinges?
Width changes the lever arm relative to the hinges, while height and mass change the loads on the entire group. Check the diagram for the specific hardware.
Open answer Technical catalogueShare the answer276.What is the sash rebate dimension?
This is the dimension specified by the system in the rebate area. When selecting hardware, it must be measured according to the manufacturer's diagram.
Open answer Technical catalogueShare the answer277.What is a liftable window handle used for in a child-safety system?
Some systems allow you to select the opening mode first, while full opening is protected by a key. Check the control sequence of the specific product.
Open answer Technical catalogueShare the answer278.When is it impossible to repair a window by replacing just one component?
If a connection is chipped, several mechanisms are stretched or replacement parts are no longer suitable, the entire drive chain and its compatibility must be assessed.
Open answer Technical catalogueShare the answer279.Why is the handle of sliding sashes difficult to operate?
The handle may control several mechanisms. It is important to distinguish whether the problem is with switching, sash movement along the track or locking.
Open answer Technical catalogueShare the answer280.Where can the marking of a sliding door system be found?
Check the visible drive rod, carriages or guide elements. An overall system photograph helps distinguish its type.
Open answer Technical catalogueShare the answerAdditional design and installation
281.Why is the installation thermal bridge not the same as the window Uw?
Uw describes the window as a product. Heat losses through the installation junction depend on the position of the frame in the wall and the wall junction itself.
Open answer Technical catalogueShare the answer282.What is the linear thermal bridge coefficient?
It describes additional heat transfer per unit length of the joint. It applies to edges, such as glass and frame or window and wall junctions.
Open answer Technical catalogueShare the answer283.Why is the proportion of glass fields important for the same façade?
Large and elongated fields behave differently under load. The size, shape, and supports of the structure itself must be assessed together.
Open answer Technical catalogueShare the answer284.What is the difference between wind pressure and wind suction?
The wind can press against the plane or pull it away from the building. Fastening and profiles are selected for both important load directions.
Open answer Technical catalogueShare the answer285.Why is the fastening selected according to the wall material?
The engagement of the fastener differs in concrete, masonry, and other walls. The substrate, edge distances, and intended loads are important.
Open answer Technical catalogueShare the answer286.Do installation wedges and support blocks perform the same function?
Temporary wedges help determine the position. Permanent supports must transfer the load according to the selected junction design.
Open answer Technical catalogueShare the answer287.Why is it necessary to check how the window opens after installation?
Frame position deviations or bending change the gaps. Check the sash movement, lock, and compression before finishing the interior surfaces.
Open answer Technical catalogueShare the answer288.How does sealing tape differ from installation foam?
The tape performs the sealing function of the intended layer. Foam mainly fills the joint and provides thermal insulation.
Open answer Technical catalogueShare the answer289.Why should the installation gap of a dark window not be copied from that of a white window?
Surfaces in the sun can heat up unevenly. Select the gap according to the specific profile system, color, and dimensions.
Open answer Technical catalogueShare the answerMicroclimate
Microclimate
290.What is relative humidity?
It shows how much moisture is in the air compared with the maximum amount the air can hold at that temperature.
Open answer Check the risk of condensationShare the answer291.What is the dew point?
It is the temperature at which moisture begins to condense as the air cools. The more humid the air, the higher the dew point.
Open answer Check the risk of condensationShare the answer292.Why does humid air condense on a cold window?
The air cools down near the cold glass. If the glass surface temperature falls to the dew point, droplets form on it.
Open answer Check the risk of condensationShare the answer293.Does opening a window briefly in winter reduce humidity?
Usually, cold outdoor air contains less absolute moisture. Once the incoming air warms up, it has lower relative humidity. The result depends on air exchange and sources of moisture in the room.
Open answer Check the risk of condensationShare the answer294.Why is it cool near the window even though the room is warm?
Cold glass reduces thermal comfort, and a flow of cooled air may descend near it. Compare whether the movement is felt at the glass or at the leaky joint.
Open answer Advice from a specialistShare the answer295.Why does street noise become louder when a window is opened slightly?
An open opening becomes a direct path for sound. If both air and quiet are needed, it is worth assessing acoustic air supply and extraction.
Open answer Advice from a specialistShare the answer296.How can you check whether the extractor helps with ventilation?
It is important that air enter the rooms, have a path through the dwelling, and be removed in the bathroom or kitchen. An air inlet without extraction may not be sufficient.
Open answer Advice from a specialistShare the answer297.Does an airtight window ventilate a dwelling by itself?
A closed, airtight window does not reliably supply the room with outdoor air. Air supply and extraction must have designated paths.
Open answer Advice from a specialistShare the answer298.Why does a room overheat near a large window?
Solar energy enters through the glass. Assess the orientation, the solar factor of the glass, outdoor shading, and the possibility of ventilating the room.
Open answer Advice from a specialistShare the answerAdditional microclimate diagnostics
299.How does absolute humidity differ from relative humidity?
Absolute humidity describes the amount of water vapor in the air. Relative humidity also depends on air temperature, so it can be reduced by heating without removing the vapor.
Open answer Check the risk of condensationShare the answer300.Does heating remove moisture from the room?
Heating can reduce relative humidity, but removing water vapor requires air exchange or dehumidification.
Open answer Check the risk of condensationShare the answer301.Why is it important to measure humidity where condensation occurs?
The conditions in the room and in the window area itself differ. Compare the room air humidity and temperature with the coldest glass or reveal surface.
Open answer Check the risk of condensationShare the answer302.How does the window's sound insulation differ from street noise?
Insulation describes how much the structure reduces sound. The noise level in the room also depends on the outdoor source and other sound paths.
Open answer Advice from a specialistShare the answer303.Why are the acoustic data for the glass alone insufficient?
Sound transmission is determined by the entire junction. It can be worsened by the sash gap, air inlet, installation joint, or adjacent wall.
Open answer Advice from a specialistShare the answer304.Can closing the interior doors worsen ventilation?
If air no longer has a path from the inlet to the extraction point, the flow weakens. The ventilation plan must also include air transfer between rooms.
Open answer Advice from a specialistShare the answerFaults and maintenance
Hardware
305.What is window hardware?
These are the handles, drives, hinges, stays, and locking components that allow the sash to be opened, tilted, and pressed against the frame.
Open answer Advice from a specialistShare the answer306.What is the difference between opening and tilting?
When opening, the sash rotates around the lateral hinge axis. When tilting, the top leans into the room while the bottom remains at the support point.
Open answer Advice from a specialistShare the answer307.What do the upper window stays do?
They control and limit the movement of the top of the tilted sash. If the handle turns but the top does not tilt, the stays and the movement transmission to them are checked.
Open answer Advice from a specialistShare the answer308.How does the handle move the locking pins?
The handle spindle turns the central drive. Through moving rods and corner drives, it transmits movement to the locking points.
Open answer Advice from a specialistShare the answer309.What is a corner drive?
It transmits movement from one sash edge to the other around a corner. If it fails, the locking points farther along may stop moving.
Open answer Advice from a specialistShare the answer310.What is a striker plate?
It is a component attached to the frame that the sash locking pin enters when the sash is closed. Their alignment is important for locking and compression.
Open answer Advice from a specialistShare the answer311.What is the purpose of a mishandling device?
It helps prevent the handle from being moved to the wrong position when the sash is open. Do not force the handle if it gets stuck.
Open answer Advice from a specialistShare the answer312.What is the purpose of a sash lifter?
When closing, it helps the sash move into the correct position. If the sash catches at the bottom, it is worth checking its geometry and the alignment of the lifting block and striker plate.
Open answer Advice from a specialistShare the answer313.Why is different hardware used for a top-hung vent located high up?
The upper tilt section must be operated from an accessible location. The mechanism transfers movement to the tilt stays.
Open answer Advice from a specialistShare the answer314.What does a child window lock do?
Depending on the system, it limits full opening or locks the handle. Check which mode the specific product allows.
Open answer Advice from a specialistShare the answer315.How does an opening restrictor work?
The limiter stops the sash at a selected or structurally designated position. Its purpose and fastening must be coordinated with the window system.
Open answer Advice from a specialistShare the answer316.How do mushroom-shaped pins increase resistance to forced entry?
The locking pin engages with the designated striker component. The resistance of the entire construction also depends on the glass, profile, fastening and assembly.
Open answer Advice from a specialistShare the answer317.Does replacing only the locking pin make the window burglary-resistant-certified?
The resistance class applies to the tested construction. Replacing one component alone does not substantiate the class of the entire window.
Open answer Advice from a specialistShare the answer318.How does a tilt-and-slide sash work?
The sash moves away from the sealing plane and travels on a track parallel to the frame. Some systems also allow it to tilt.
Open answer Advice from a specialistShare the answer319.How do folding doors differ from sliding doors?
The sashes of folding doors fold to the side like an accordion. Their hinges, carriages and guides work together.
Open answer Advice from a specialistShare the answer320.How does a multipoint door lock work?
One drive operates several locking points at different heights. Their travel and striker components must correspond to the sash position.
Open answer Advice from a specialistShare the answer321.Does the same number of locking points mean the same hardware?
The drive travel, distances, components and their connection differ. When replacing them, the manufacturer, markings and dimensions must be checked.
Open answer Advice from a specialistShare the answerAutomation and safety
322.What is an electric window drive used for?
It moves the sash to the designated position according to a command or sensors. Compatibility depends on the sash, hardware and drive travel.
Open answer Advice from a specialistShare the answer323.Why is it important to determine the locking status for an automated window?
A closed-against-the-frame sash may still be unlocked. The control system must take into account the perimeter locking position and the system design.
Open answer Advice from a specialistShare the answer324.What does a rain sensor do on an automated window?
When it detects precipitation, it can send a closing command. Operation depends on the sensor location, controller and settings.
Open answer Advice from a specialistShare the answer325.How does periodic ventilation differ from continuous air supply?
The opening is periodically opened for a set time. Continuous air supply is intended to maintain airflow through the designated inlet.
Open answer Advice from a specialistShare the answer326.How does a wall-mounted air inlet differ from a window air inlet?
It is installed in the wall, so the air path, filtration and sound attenuation can be addressed separately from the window.
Open answer Advice from a specialistShare the answer327.What is the difference between an opening sensor and a glass-break sensor?
One tracks the sash position. The other detects a sign characteristic of glass breakage. They monitor different events.
Open answer Advice from a specialistShare the answer328.Why does automated smoke extraction require a separate solution?
Smoke extraction windows and drives are part of the building's fire safety system. Their operation must be specified in the particular project.
Open answer Advice from a specialistShare the answer329.Why is it necessary to control both shading and ventilation in a conservatory?
Shading limits the entry of solar heat. Ventilation helps remove excess heat and moisture. The control system can coordinate both according to the sensors.
Open answer Advice from a specialistShare the answer330.Why must an automatic sash have a designated safe operating mode?
A moving sash can trap a person or an obstacle. Accessibility, the control method and the protections of the specific system are assessed.
Open answer Advice from a specialistShare the answerAdditional automation
331.What must the automation do when the wind or rain changes?
The actions depend on the sensors and the defined priorities. First, it is determined which commands take precedence for safety and weather conditions.
Open answer Advice from a specialistShare the answer332.How does decentralized ventilation differ from a central system?
Decentralized units serve one or several zones locally. A central system usually distributes airflow through ducts from a common unit.
Open answer Advice from a specialistShare the answer333.Does a magnetic window contact indicate that all locks are locked?
A simple contact usually indicates the sash position. Determining the lock status requires a sensor adapted for this purpose or feedback from the hardware.
Open answer Advice from a specialistShare the answer334.Why is an outdoor sensor important for conservatory windows?
Outdoor conditions help control ventilation and protection from rain or wind in advance. Indoor sensors supplement the information about comfort.
Open answer Advice from a specialistShare the answerExterior doors
335.Which profile is used for PVC exterior doors?
The profile series cannot be reliably determined from appearance alone. A system marking, profile cross-section or manufacturer's documents are required. Upload a photo of the marking or the edge of the open door.
Open answer Advice from a specialistShare the answer336.What reinforcement and steel thickness are used in exterior doors?
A steel wall thickness of only 2 or 3 mm does not prove that the door is properly reinforced. For the specific system, the shape and thickness of the steel profile, its location and fastening, the permitted sash dimensions and the stiffness requirements are checked. The profile series or reinforcement marking is required; there is no universal 2–3 mm answer.
Open answer Advice from a specialistShare the answer337.How are the corners of PVC exterior doors welded?
At the corners, the prepared profile ends are welded together. The overlap, weld bead projection and cleaning dimensions depend on the profile system and equipment settings. There is no universal distance in centimetres from the outer corner. Please specify whether you are asking about the weld length, depth, cleaning allowance or distance to the lock cutout.
Open answer Advice from a specialistShare the answer338.What is the difference between a lift handle and a lock with a cylinder-operated drive?
When the handle is lifted, a handle-operated multipoint lock can extend hooks or locking pins, while the key locks it in place. A cylinder-operated drive is locked by turning the key; automatic and electromechanical systems work differently. The specific lock model is important. Photograph the marking on its edge.
Open answer Advice from a specialistShare the answer339.Which dimensions should be checked before routing the lock?
Based on the lock model and the manufacturer's template, the backset, PZ distance, square spindle size, faceplate width and length, case dimensions and the locations of the locking points are checked. There is no universal distance from the outer corner. Before cutting, confirm the door profile and lock model.
Open answer Advice from a specialistShare the answerDoor malfunctions
340.Why does the door catch on the frame or threshold?
If the sash catches on the frame or threshold, note where it catches: at the top, bottom or near the lock. This helps distinguish a hinge adjustment, sash geometry or threshold problem. Do not force the door; a photo of the closing area will help the technician.
Open answer Perform a fault analysisShare the answer341.Why does the door handle or key prevent the door from closing?
If the sash does not close or lock, check whether the handle and key move when the door is already open. If they work with the door open but jam when it is closed, the locking points may not align with the striker plates. If they also jam when open, the lock, cylinder or drive should be checked. Do not turn it by force.
Open answer Perform a fault analysisShare the answer342.Why does the door close but not lock?
Check whether the sash fits fully against the frame and whether the locking pins reach the striker plates. With some multipoint locks, the handle must be lifted before locking; with others, the mechanism is operated by the key or automatically. The exact operation depends on the lock model. Photograph the lock marking and the place where it jams.
Open answer Perform a fault analysisShare the answer343.What should I do if the exterior door does not close fully?
First determine whether the sash, threshold, seal or locking mechanism is catching. If the door is the only exit, do not block it or dismantle the lock. State where it stops and attach photos of the sash edge and frame; the technician will use them to уточнить the fault.
Open answer Perform a fault analysisShare the answerMaintenance
344.Why is WD-40 unsuitable for window hardware?
Universal WD-40 may temporarily make movement easier, but it is not a long-term lubricant for window hardware. It can wash out the previous lubricant, after which the mechanism may start sticking and wearing. Clean off the dirt and sparingly lubricate the moving metal components with a lubricant intended for window hardware that does not damage seals. If the handle sticks, also check the sash geometry and compression.
Open answer Advice from a specialistShare the answerStronger compression is not always better
Excessive compression squeezes the seal, makes the handle harder to operate and increases the load on the drive. We adjust it only after assessing the sash geometry and the position of the closing points.
Where does condensation accumulate?
Moisture on the room side is usually related to surface temperature and air exchange. Moisture between the panes indicates lost insulating glass unit tightness. Condensation outdoors may be a sign of a good thermal insulating glass unit.
Register a window or door inspection
Briefly describe the fault, indicate the city and, if possible, send a general photo of the construction and hardware. Call+370 612 45 700.
Where we work
We come to Klaipėda and the surrounding cities and settlements: Palanga, Šventoji, Gargždai, Kretinga, Šilutė, Slengiai, Ginduliai, Vėžaičiai, Dovilai, Priekulė and Dreverna. We arrange the arrival time in advance.